← Back to the blog

Basics

Audio cables: RCA, XLR, speaker cables and what really matters

· 16 min read

In short: A cable cannot make the sound better. It can only make it worse. A good cable is one that carries the signal without loss and without interference. With signal cables, what matters most is whether the connection is balanced (XLR) or unbalanced (RCA). XLR resists interference and suits long runs. RCA is perfectly fine for short connections at home. With speaker cables, only resistance matters, which means cross-section and length. For normal lengths, plain copper twin-core cable of 1.5 to 2.5 mm² is enough. Cables costing hundreds of euros, cable direction and “burn-in” find no support in blind tests.

In this article:

  1. What cables a system has
  2. RCA: the unbalanced connection
  3. XLR: the balanced connection
  4. RCA and XLR side by side
  5. Hum and ground loops
  6. How to connect XLR to RCA
  7. When cable capacitance matters: the turntable
  8. Speaker cables: the right cross-section is enough
  9. Connectors and terminations
  10. Digital cables: coax, optical, USB, HDMI
  11. Cable myths
  12. Cables when building a speaker
  13. What to buy: a quick overview
  14. Short glossary

What cables a system has

In a home system you will meet three groups of cables. Each has a different job, and something different matters for each.

GroupWhat it carriesExamplesWhat matters
Signal (analog)a weak voltage, around 0.3 to 4 V, almost no currentRCA, XLR, jackresistance to interference, shielding, capacitance for a turntable
Speakera strong signal from the amplifier, current in amperestwin-core cable with banana plugs or bare endsresistance, which means cross-section and length
Digitalnumbers, not a sound wavecoaxial S/PDIF, optical, USB, HDMIwhether the data arrives complete, sometimes ground isolation

A signal cable is like a thin water pipe that only carries “pressure”. A speaker cable is like a thick hose that has to move a lot of water. That is why they have completely different requirements.

RCA: the unbalanced connection

The RCA connector, also called cinch or phono plug, was introduced by the American company Radio Corporation of America in the 1930s and 1940s to connect a record player to a radio. Since then it has been the most common connector in home audio: CD player, DAC, turntable, amplifier, subwoofer.

An RCA cable has one signal conductor in the middle and a shield around it, either a braid or a foil. The shield has two jobs at once: it protects the signal from interference and it is also the return conductor, the ground. The device measures the voltage between the centre and the shield.

That is the weak spot. Anything that gets induced into the shield, or flows through it from another path, is added straight to the music. On a short run in the living room this does not matter. On a long cable, next to mains cables, or when devices are grounded through different paths, it is a source of hum and noise.

  • Typical level: consumer electronics around 0.3 V (the so-called −10 dBV), CD players and DACs usually 2 V at full scale.
  • Sensible length: up to 3 to 5 m with no problems, longer depending on the surroundings.
  • Pros: cheap, everywhere, simple.
  • Cons: sensitive to interference and ground loops, the connector can work loose, you cannot tell which end is which channel unless it is colour-coded.

XLR: the balanced connection

The XLR connector was created in the 1950s by the Cannon company. The name comes from the X series, to which they added a latch (Latch) and rubber insulation (Rubber). It is the standard in studios and on stage, and more and more common in hi-fi too: on better DACs, preamplifiers and active speakers.

XLR has three pins. According to the standards (IEC 60268-12, AES14):

  • pin 1: shield and ground,
  • pin 2: “hot” signal (+),
  • pin 3: “cold” signal (−).

The trick is that the signal travels on two conductors, and the shield has nothing to do with it. Pin 2 carries the music as it is, pin 3 carries it flipped upside down. Both conductors sit tightly together in the cable and are twisted, so any interference picked up on the way is induced equally into both. The device input subtracts one conductor from the other: the music doubles, while the interference, the same on both, cancels out.

Top, an unbalanced connection (RCA): the music travels on one conductor, interference adds to it, and music with hum arrives at the input. Bottom, a balanced connection (XLR): the music travels on two conductors, once as it is (gold) and once flipped (blue). Interference gets into both equally. The input subtracts them, the interference disappears and clean music remains.

A good balanced input typically suppresses interference a hundred to a thousand times (40 to 60 dB) or more. That is why a microphone cable at a concert can be 50 m long and still not hum.

  • Typical level: professional gear around 1.2 V (the so-called +4 dBu). Hi-fi DACs usually put out twice the RCA voltage on XLR, for example 4 V instead of 2 V, which is 6 dB more.
  • Sensible length: tens of metres.
  • Pros: resists interference, less hum from ground loops, a sturdy connector with a latch.
  • Cons: more expensive, bigger, not every device has it. The advantage only applies when both the output and the input are balanced.

You will also find balanced connections on the 6.3 mm jack with three contacts (TRS): the tip is +, the ring is − and the sleeve is ground. Studio sound cards and monitors often have it. Careful: a jack with two contacts (TS) is unbalanced, just like RCA.

RCA and XLR side by side

RCAXLR
Connection typeunbalancedbalanced
Conductorssignal and shieldtwo signal conductors and a separate shield
Resistance to interferenceweakervery good
Hum from ground loopscommonrare
Sensible lengthup to 3 to 5 meven tens of metres
Typical level0.3 to 2 V1.2 to 4 V
Connectorsimple, push-onwith a latch, rugged
Pricelowhigher
Where it is usedhome hi-fi, TVs, subwoofersstudio, stage, active speakers, better DACs

When to use which: for a short connection between a DAC and an amplifier in the same rack, RCA is perfectly fine. A well-made RCA cable sounds the same as XLR here. XLR is worth it when you run the signal across the room to active speakers or a subwoofer, when there is a computer in the chain, when you hear hum, or when both devices have it and it costs the same.

Hum and ground loops

The most common cable problem is not “the sound of the cable” but hum: a quiet buzz at the mains frequency, 50 Hz and its multiples. It is almost always caused by a ground loop.

How it happens: two devices are grounded through the wall socket, each by a different path, and they are also connected by the cable shield. This creates a closed loop. There is always a small voltage difference between different sockets, so a weak current flows through the shield. With RCA, the shield is also the signal return conductor, so the voltage from this current is added to the music.

Typical culprits:

  • a TV or set-top box with an aerial or cable TV, whose ground comes from the whole building,
  • a computer, especially a desktop, and its sound card,
  • a subwoofer plugged into a different socket on the other side of the room,
  • chargers and power supplies for laptops and phones.

How to get rid of it, simplest first

  1. Plug everything into one power strip. The loop gets smaller and the voltage difference drops. This helps surprisingly often.
  2. Find the culprit. Unplug cables one by one, starting with the aerial and the computer. When the hum disappears, you know where it is.
  3. A shorter cable with a heavy shield. With RCA, the resistance of the shield matters, not of the centre conductor.
  4. An aerial ground isolator (galvanic isolator) for a few euros, if the hum comes through the TV cable.
  5. An isolation transformer in the signal path (a so-called ground loop isolator). Cheap ones can take a little off the deepest bass, good ones are inaudible.
  6. A balanced connection (XLR), if the devices have it.
  7. An optical digital cable between the source and the DAC. Optical does not conduct electricity, so it breaks the loop completely.

Careful: never disconnect the earth pin in the plug and do not use adapters that leave out the ground. The hum goes away, but if there is a fault, the device chassis can become live. Protective earth is there to protect your life, not the sound.

Hum can also be caused by a badly designed device. In 1995 Neil Muncy described the so-called pin 1 problem: the manufacturer connects the XLR shield to the circuit ground inside the device instead of to the metal chassis at the connector. Interference from the shield then flows through the sensitive electronics. In that case even an expensive cable will not help, only a better device.

How to connect XLR to RCA

In practice you often need to connect a balanced device to an unbalanced one. It can be done, but keep in mind that the interference rejection advantage is at least partly lost.

From an RCA output to an XLR input

For example from a phono preamp to an active speaker. The best way is to use a two-core shielded cable: pin 2 to the RCA centre conductor, pin 3 to the RCA ground at the source end and the shield to pin 1. The balanced input then still subtracts the interference picked up on the way, and most of the advantage remains. A simpler cable where pins 1 and 3 are joined right inside the XLR connector also works, it just protects less.

From an XLR output to an RCA input

For example from a DAC with an XLR output to an older amplifier. Pin 2 goes to the centre conductor, pin 1 to ground. Pin 3 is most often connected to ground. Most outputs can handle this, and transformer outputs even need it, but some electronic outputs cannot. So check the device manual. The signal level drops by half, which is 6 dB, and that usually does not matter.

If a cable connects the shield at only one end, the manufacturer often marks it with an arrow. This is the only case where “cable direction” has a technical meaning: the arrow shows where the shield is connected, not which way the cable sounds better.

When cable capacitance matters: the turntable

Every cable has a small capacitance, the ability to store charge like a capacitor. A normal RCA cable has 50 to 150 pF per metre. Together with the output resistance of the source it forms a filter that cuts treble. With normal electronics this is completely negligible:

SourceOutput resistanceCableWhere the treble starts to drop
transistor DAC or preamparound 100 Ω5 m (about 500 pF)3 MHz, far above hearing
tube preamparound 2 kΩ5 m (about 500 pF)160 kHz, still no effect
10 kΩ passive volume control, worst position2.5 kΩ10 m (about 1,000 pF)64 kHz, a 0.4 dB loss at 20 kHz

The exception is a turntable with a moving magnet (MM) cartridge. Such a cartridge has a coil with a large inductance, around 0.5 H. Together with the capacitance of the cable and the input, the coil forms a resonant circuit that creates a bump in the treble and a steep drop above it. That is why the manufacturer states what total capacitance the cartridge wants, usually 100 to 200 pF. This includes the tonearm cable and the preamp input.

-12-9-6-30+3+61 kHz2 kHz5 kHz10 kHz20 kHzdB123
Electrical response of an MM cartridge (0.5 H, 1 kΩ) into a 47 kΩ input at different total capacitance of cable and input: 1 is 100 pF, 2 is 250 pF, 3 is 500 pF. As the capacitance grows, the bump moves lower, gets bigger and the treble above it falls faster. At 500 pF the bump is about +3.5 dB around 9 kHz and 10 dB is missing at 20 kHz. The manufacturer tunes the cartridge so the whole response is flat at the capacitance it specifies.

So here you really can hear the cable, and it is not a myth. With an MM cartridge, use a short, low-capacitance cable and follow the cartridge maker’s recommendation. Moving coil (MC) cartridges have a thousand times less inductance and are not sensitive to capacitance.

Speaker cables: the right cross-section is enough

A speaker cable carries a strong current, and its only important property is resistance. Resistance depends on the material, the cross-section and the length. For copper there is a simple formula:

Cable resistance = 0.0172 × 2 × length in m / cross-section in mm². The 2 is there because the current goes there and back. For example, 5 m of 1.5 mm² twin-core cable has 0.0172 × 10 / 1.5 = 0.115 Ω.

Why resistance matters

Cable resistance does three things:

  1. It reduces volume. Part of the power turns into heat in the cable. With 0.1 Ω and a 4 Ω speaker, that is about 0.2 dB, which is unimportant. Just turn the volume up a little.
  2. It changes the response. This one matters more. A speaker’s impedance is not constant. With a 4 Ω speaker it drops to, say, 3.2 Ω and rises to 30 Ω or more at resonance. The cable and the speaker form a voltage divider that divides differently at each impedance. Where the impedance is high, more voltage arrives. Where it is low, less. So the response gets a little wavy.
  3. It weakens bass control. The amplifier damps the cone’s movement through its low resistance. The cable resistance adds to the voice coil resistance, and the driver’s Qes rises slightly. With a 3.2 Ω voice coil and 0.25 Ω of cable plus amplifier, the Qts of a driver with Qes 0.40 and Qms 4 rises from 0.36 to 0.39, about 7%. With 10 m of thin 0.75 mm² twin-core cable, it is already 14%. The bass then gets a bit softer and slightly bloated.
00.511.520 m5 m10 m15 m20 mdB1234
How many decibels the response of a 4 Ω speaker ripples, with impedance varying from 3.2 to 30 Ω, depending on the length of copper cable: 1 is 0.75 mm², 2 is 1.5 mm², 3 is 2.5 mm², 4 is 4 mm². The dashed line is 0.5 dB, a strict limit below which the change cannot be heard. With an 8 Ω speaker the changes are roughly half as big.

What cross-section for what length

A common rule says that the cable resistance should be at most 5% of the speaker’s nominal impedance. Then the response ripples by at most half a decibel. For copper cable, this gives:

Cross-section (approx. AWG)Maximum length for 4 ΩMaximum length for 8 Ω
0.75 mm² (AWG 18)4.4 m8.7 m
1.5 mm² (AWG 16)8.7 m17 m
2.5 mm² (AWG 14)14.5 m29 m
4 mm² (AWG 12)23 m46 m

The length is the length of the cable, not the whole loop. For a normal living room with 2 to 5 m per speaker, 1.5 mm² is enough, 2.5 mm² gives you headroom. A thicker cable does no harm, but it no longer helps either.

What else does not matter

  • Inductance of normal twin-core cable is around 0.5 µH per metre. At 5 m this makes hundredths of a decibel at 20 kHz.
  • Capacitance of twin-core cable is small and does not bother the amplifier. Only watch out for exotic cables with very high capacitance, which can make some amplifiers without an output coil oscillate.
  • Skin effect, the current being pushed to the surface of the conductor: at 20 kHz the current penetrates about 0.46 mm into copper. With normal cross-sections this raises the treble resistance by a few percent, which is thousandths of an ohm.
  • Oxygen-free copper (OFC) has almost the same resistance as ordinary copper. Its only advantage is less corrosion. Silver has 8% lower resistance, and you get the same effect with a slightly thicker copper cable.

Watch out for CCA: cheap cables are often made of copper-clad aluminium (copper clad aluminium). They have about 1.6 times the resistance of copper of the same cross-section, are harder to solder and break more easily. You can spot them because the core of the strand is silver after you scrape it. A 2.5 mm² CCA cable behaves like a 1.5 mm² copper one.

Bi-wiring and bi-amping

Bi-wiring means that the crossover in the speaker has two pairs of terminals, and you run two cables to it from the amplifier, one for the bass section and one for the treble section. Electrically it is the same as one cable with twice the cross-section. The measurable difference is very small, and it has not been shown in blind tests.

Bi-amping is something else: each driver has its own amplifier. With an active crossover it is a real improvement, more in the article Passive or active crossover.

Connectors and terminations

ConnectorWhere it is usedNote
RCA (cinch)hi-fi signal, subwoofer, coaxial S/PDIFwhen buying, check that it holds firmly
XLRbalanced signal, microphones, AES/EBUmale on the output, female on the input
6.3 mm jack TRS / TSstudio gear, headphonesTRS can be balanced, TS cannot
3.5 mm jackcomputer, phone, portable devicesbetter not for a permanent setup, it works loose easily
4 mm banana plugsspeaker terminalsconvenient, hold well
spadesspeaker terminals with a screwa very firm connection
bare ends with a ferrulespeaker terminalscheap and reliable
Speakonprofessional speakerslocking, cannot be short-circuited

A good tip for bare ends: do not tin them if they go under a screw. Solder slowly creeps under pressure, so the connection loosens over time and can start to crackle. It is better to crimp on a ferrule or fit a banana plug or a spade.

Digital cables: coax, optical, USB, HDMI

A digital cable does not carry a sound wave, it carries numbers. Either they arrive complete, or the transfer obviously breaks: dropouts, crackling, silence. You will not get a “warmer” or “more detailed” sound from a digital cable.

CableWhat forSensible lengthNote
coaxial S/PDIF (RCA)CD, streamer, TV → DACup to 10 mthe correct cable is 75 Ω, but a normal RCA cable is fine for short runs
optical (Toslink)TV, console, streamer → DAC or soundbarup to 5 to 10 mdoes not conduct electricity, breaks a ground loop; some devices limit resolution to 96 kHz
USBcomputer → DACup to 5 man asynchronous DAC takes the data on its own clock; the only usual problem is ground noise from the computer
HDMI ARC / eARCTV → AV receiver or soundbarup to 5 to 10 meARC needs a cable that can handle a higher speed

The bogeyman called jitter, timing wobble of the clock, is handled by the DAC itself these days. More on that in the article Analog or digital. With USB, the computer can bring noise in through the ground. A different port, a powered hub or a USB isolator helps, not a more expensive cable.

Cable myths

More money and faith revolve around cables than around anything else in audio. Here is what measurements and blind tests show:

  • An expensive speaker cable sounds better. In a blind test by Stereo Review magazine (Greenhill, 1983), only a very thin cable with a resistance of 1.8 Ω could be heard. Ordinary twin-core cable of around 1.3 mm² could not be told apart from an expensive brand-name cable.
  • A cable has a direction. The alternating current of music flows back and forth all the time. An arrow only means something on cables where the shield is connected at one end.
  • A cable needs to burn in. With drivers, the suspension really does loosen a little during the first hours. With a cable, nobody has shown it by measurement. It is more likely your ear getting used to it.
  • A power cable for hundreds of euros improves the sound. The last metre of cable changes nothing about the tens of metres of wiring in the wall. The amplifier’s power supply rectifies and smooths the voltage anyway.
  • Cryogenically treated, directionally drawn, with “stabilisers”. The manufacturers do not provide measurements that would show a difference at the output.
  • An expensive digital cable. If the numbers arrive complete, they arrive complete. A measurable difference only appears with a fault or ground noise.

In 2007, when a maker of a $7,250 cable agreed to a million-dollar blind test, it pulled out before the test. More on how to compare fairly is in the article Hi-fi and high-end. You can also check differences yourself in the ABX blind test.

This does not mean all cables are the same. You really can hear a bad cable: a speaker cable that is too thin, a poorly shielded RCA cable next to mains wiring, a loose connector, a high-capacitance cable on a turntable, a broken strand. These are all measurable faults, and they can be fixed cheaply.

Cables when building a speaker

When you build your own box, you also deal with the internal wiring. The same rules apply, the lengths are just short.

  • Internal wiring: 1 to 1.5 mm² for the woofer, 0.75 to 1 mm² for the tweeter. For lengths up to half a metre, that is more than enough.
  • Connecting the drivers: smaller drivers have 2.8 mm Faston connectors, bigger ones 4.8 mm or 6.3 mm. Faston holds well, no soldering needed.
  • Polarity: the driver’s plus is usually marked with a red dot or a wider connector. On a woofer you can check it with a 1.5 V battery: plus to plus, and the cone moves outward. Do not connect a battery to a tweeter.
  • Twist the wires into a pair. A twisted pair picks up less interference and has lower inductance.
  • Route the wires away from the crossover coils and turn the coils 90° to each other so they do not affect each other. Loudsmith takes care of this when designing the crossover circuit board.
  • Glue or fasten the wires so they do not slap against the cabinet wall on loud bass notes. A rattling wire is a common and annoying source of noise.
  • Seal the cable hole with silicone or a gasket, especially in a sealed box and a bass reflex. A leak whistles and changes the tuning.

What to buy: a quick overview

UseRecommendationApproximate price
Speaker cable up to 5 mcopper twin-core 1.5 to 2.5 mm², not CCA€1 to €3 per metre
Speaker cable over 10 m2.5 to 4 mm²€2 to €5 per metre
RCA between devices in a racka well-shielded cable with firm connectors, as short as possible€5 to €20
Long run to active speakers or a subwooferXLR, if the devices have it; a microphone cable from a known maker€10 to €25 each
Turntable with an MM cartridgea short, low-capacitance cable as the cartridge maker recommends€10 to €30
Digital from a TVoptical cable; it also breaks a ground loop€5 to €10

Put the money you save where the differences are really big: into the speakers, their placement and the room acoustics. More in the article The room plays along.

Short glossary

  • Unbalanced connection: the signal goes out on one conductor and back through the shield. RCA, TS jack.
  • Balanced connection: the signal travels on two conductors in opposite phase, and the input subtracts them. XLR, TRS jack.
  • Shield: a braid or foil around the conductors that protects against interference.
  • Ground loop: a closed circle of grounds through sockets and cables, a source of hum.
  • Hum: a buzz at 50 Hz and its multiples.
  • Cross-section: the area of the conductor in mm². Bigger cross-section, lower resistance.
  • AWG: the American wire gauge system. A smaller number means a thicker wire.
  • Capacitance: the cable’s ability to store charge, given in pF per metre.
  • Impedance: the speaker’s “resistance” to alternating current. It changes with frequency.
  • CCA: copper-clad aluminium, a cheap substitute for copper with higher resistance.

Sources: B. Whitlock, Balanced Lines in Audio Systems: Fact, Fiction, and Transformers (JAES 1995); N. Muncy, Noise Susceptibility in Analog and Digital Signal Processing Systems (JAES 1995); Rane Note 110, Sound System Interconnection; standards IEC 60268-12 and AES14 (XLR wiring) and IEC 60958 (S/PDIF); L. Greenhill, Speaker Cables: Can You Hear the Difference? (Stereo Review 1983); R. Russell, Speaker Wire: A History; data from cartridge and cable makers. The resistance, response and cartridge calculations are our own.

Free tools: Room planner · Speaker measurement · Blind ABX test