← Back to the blog

Basics

Buy ready-made speakers or build your own?

· 13 min read

In short: In the price of a ready-made speaker, the drivers usually account for only about a tenth. Most of what you pay goes to the retailer, distribution, tax, the brand and development. Build the speaker yourself and the same money buys you far better drivers, a cabinet made to measure and a lot of know-how. The price is your time, tools and the risk that the result won't sound as good as you hoped. The hardest part isn't the cabinet, it's the crossover. The safest route for a first build is a proven design or a kit. Below €300 a pair, building barely pays off financially. From around €800 a pair of ready-made speakers upwards, it does.

In this article:

  1. Where the money goes in a ready-made speaker
  2. The maths: a €1,000 speaker
  3. What you gain by building
  4. What building costs you
  5. Why the crossover is the hardest part
  6. Kits and proven designs: the safe middle road
  7. Example: a DIY two-way versus a ready-made speaker
  8. What tools you need
  9. Common beginner mistakes
  10. Resale value
  11. When to buy, when to build
  12. How Loudsmith helps
  13. Key takeaways
  14. Short glossary

Where the money goes in a ready-made speaker

When you buy a pair of speakers in a shop, you are paying a whole chain of people and companies. The manufacturer buys the drivers and parts, builds the cabinet, assembles the speaker and packs it. Then an importer brings it into the country, and a retailer puts it on display, advises you and gives you a warranty. The state adds VAT. Everyone in the chain has to cover their costs and make something on top.

Companies don't publish exact figures, and they vary by brand and by how the speaker is sold. But the industry keeps painting roughly the same picture: all the "hardware" together, meaning drivers, crossover, cabinet and assembly, makes up roughly a fifth to a third of the shelf price. The drivers themselves are the smaller part of that.

0 %10 %20 %30 %40 %12345678
Approximate share of each item in the shop price of a passive speaker, in percent. The solid bar is the low end and the light bar the high end of the typical range; gridlines every 5 %. Top to bottom: 1 drivers, 2 crossover parts, 3 cabinet and finish, 4 assembly, terminals, packaging and shipping from the factory (1 to 4 in gold: hardware), 5 manufacturer: development, marketing, warranty and profit, 6 import and distribution, 7 retailer (5 to 7 in blue), 8 VAT at 23 % (the Slovak rate), which is 18.7 % of the price including tax (in red). This is a rough model, not data from any particular company.

The chart tells you two things. First, the biggest items are the retailer and tax. Second, the price covers a lot of things that building neither gives you nor takes away: development and measurement, the warranty, and the chance to hear the speaker before you buy and return it.

Companies that sell direct online, with no importer or retailer, have a larger hardware share. That's why they often offer more for the same price. Likewise, big manufacturers with huge production runs buy drivers and cabinets far more cheaply than you can. With cheap speakers, you will almost never beat them at home.

The maths: a €1,000 speaker

Let's break it down with a concrete example. A pair of two-way bookshelf speakers costs €1,000 in the shop, including VAT. The margin percentages are typical values, not figures from a single company.

StepCalculationAmount per pair
Shop price€1,000
VAT 23 % (Slovakia)1,000 − 1,000 / 1.23€187
Retailer margin, about 35 % of the price excluding VAT0.35 × 813€285
Retailer buys from the importer for813 − 285€528
Importer margin, about 25 %0.25 × 528€132
Importer buys from the manufacturer for528 − 132€396
Manufacturer's development, marketing, warranty and profit, about 45 %0.45 × 396€178
Total production cost396 − 178€218

Those €218 split up roughly like this: drivers about €95, cabinet with finish about €68, crossover about €25, terminals, assembly, packaging and shipping about €30. So the drivers make up about 9.5 % of the shelf price.

There's one catch: the manufacturer buys drivers in large volumes, often for a fraction of what you'd pay in a DIY shop. Drivers that cost the manufacturer €95 would cost you roughly €150 to €250 at retail. So the saving from building is real, but smaller than the chart alone suggests.

What you gain by building

  • Better drivers for the same money. For what you'd spend on a ready-made pair, you can buy drivers one or two classes better. Especially in the mid-price range, the difference is noticeable.
  • A cabinet made to measure. Exactly the height, width and colour you want. For an alcove, a bookcase or the wall, in walnut veneer or painted to match your walls.
  • A design for your room and your amplifier. You can tune the bass for a speaker that stands against the wall or out in the room. You can match sensitivity and impedance to the amplifier you already own.
  • Know-how. After your first build, you'll understand why speakers sound the way they do. You'll start reading reviews and marketing claims in a completely different way.
  • Repairability. You know what's inside. When something breaks, you swap one part instead of hunting for a repair shop.
  • The joy of it. For many people, this is the main reason. Music from a speaker you built sounds different simply because it's yours.

What building costs you

Time

A proven design with pre-cut panels takes two to four weekends: gluing, drying, sanding, finishing, soldering the crossover and assembly. The finish often takes longer than everything else put together, because every coat of lacquer or paint has to dry. Your own design with measuring and crossover tuning takes weeks to months.

Tools

If you have none, expect a one-off outlay of roughly €150 to €400. Details below in What tools you need. If you already have a workshop, it's close to zero.

Risk

  • Cabinet quality. Crooked cuts, leaky joints and ugly edges are common on a first build. A leak also changes the bass tuning and can whistle.
  • Sound. Your own design without measurements can sound worse than a cheap ready-made speaker. Not because the drivers are bad, but because of the crossover.
  • Money. You can't return a ruined panel. Or a burnt-out tweeter.
  • No warranty on the whole thing. You have one on the drivers, but not on your work.

Why the crossover is the hardest part

The cabinet is woodwork. You can learn it, and if you build it to the drawing, it will work. Volume and port tuning are easy to calculate well, as the article Speaker box calculations shows.

The crossover is a different story. Its job is to send the bass to the woofer and the treble to the tweeter so that the two blend smoothly at the crossover point. On paper it looks simple: a few coils and capacitors. In practice you run into three problems at once:

  • Driver impedance isn't constant. The box says 8 Ω, but it rises at higher frequencies because the driver's voice coil has inductance. The formulas in online calculators assume a constant resistance. A crossover built from them then splits the signal somewhere other than where you wanted.
  • The driver itself isn't flat. It has its own dips and peaks, which add to the crossover's response. The result depends on how the driver behaves in your cabinet, not in the catalogue.
  • The cabinet changes the sound. Wide bass waves "wrap" around the front panel into the room, while treble goes straight ahead. This creates a difference of up to about 6 dB between them, the so-called baffle step. The edges of the panel also cause reflections.

That's why experienced designers build the crossover around measurements of the drivers in the finished cabinet. Measuring isn't expensive: a USB microphone and free software are enough, but it takes a bit of practice. The process is in the article How to measure a loudspeaker. How the pros work is described in How experienced designers work.

The alternative is an active setup with DSP, where you set the crossover on a computer and don't need to solder. That's covered in Active or passive.

Kits and proven designs: the safe middle road

Between "buy ready-made" and "design everything yourself" there's a third way that forums recommend to beginners almost unanimously: build a proven design. Someone experienced has already designed it, measured it and fine-tuned it, and dozens or even hundreds of people have built it.

RouteWhat you getSound riskYour work
Ready-made speakersa finished product with a warrantynone, you can listen before buyingnone
Kit with a pre-cut cabinetdrivers, finished crossover, cabinet partsvery lowgluing, finishing, assembly
Kit without a cabinetdrivers and crossoverlow, if you stick to the dimensionsthe whole cabinet
Proven design from a sourcedrawing and schematic, you buy the partslowcabinet and crossover soldering
Your own designwhatever you designmedium to high without measurementseverything, measuring included

An overview of well-known designers and designs, from Zaph Audio and Paul Carmody to Troels Gravesen, is in the article Famous DIY designs. For actual builds, see our build diaries for the Needle and the Tang Band and Peerless bookshelf speaker.

Example: a DIY two-way versus a ready-made speaker

Our model is the two-way bookshelf speaker from our build diary: a 13 cm woofer, a 25 mm tweeter, a passive radiator and a 9.5 l cabinet. Prices are approximate, per pair.

ItemApproximate price
Drivers: 2× woofer, 2× tweeter, 2× passive radiatorabout €256
Crossover partsabout €71
Terminals and damping materialabout €28
MDF cut to size, glue€30 to €60
Finish: paint and lacquer, or veneer€20 to €80
Total for materialsroughly €400 to €500
One-off: measurement microphoneroughly €100 to €150
One-off: tools, if you have noneroughly €150 to €400

Now let's compare that with a ready-made speaker. Drivers costing €256 at retail correspond to roughly €100 to €170 at manufacturer prices. Using the breakdown above, where drivers make up about 6 to 12 % of the price, a ready-made speaker with similar drivers would cost roughly €1,000 to €2,000 a pair in the shop.

The calculation in brief: €100 to €170 (drivers at manufacturer prices) ÷ 0.06 to 0.12 (drivers' share of the price) ≈ €800 to €2,800. The middle of that range is about €1,000 to €2,000. It's a rough estimate, not the price of any particular product.

So for €400 to €500 in materials, you get the parts of a speaker that would cost two to four times as much in a shop. What you don't get automatically is the quality of the design. You have to add that yourself, through your own work, measurements or a proven design. And if you count the tools and the microphone, your first build comes out roughly even with a ready-made mid-range pair. The savings only show from the second build on.

The opposite case: a pair of cheap bookshelf speakers for €200 to €300 from a big brand. Here you'll save practically nothing at home. The MDF, terminals, damping and shipping alone cost you €60 to €120, leaving little for the drivers. On top of that, the big manufacturer does real development, measuring in an anechoic chamber.

What tools you need

ToolWhat forEssential?Approximate price
Panel cutting at the timber yardaccurate straight cuts, most board suppliers offer itinstead of a sawa few euros per cut
Router with a circle jiground cut-outs and flush-mounting the driversvery useful€80 to €200
Jigsawcut-outs if you have no router, less accuraterouter substitute€40 to €100
Drill and a set of bitsscrews, terminals, holesyes€40 to €100
Clamps, at least 4 to 8gluing the cabinetyes€30 to €80
Soldering iron, 40 to 80 Wcrossover, thicker coil wiresyes€20 to €60
Multimeterchecking resistance, polarity and partsyes€15 to €40
Sander, or sandpaper and a blockedges, surface preparationyes€5 to €80
FFP2 mask, safety glasses, ear protectionprotection from fine MDF dust and noiseyes€15 to €30
USB measurement microphonemeasuring and tuning the crossoveryes, for your own design€100 to €150

For measuring, the free program Room EQ Wizard is all you need. If there's a workshop, a hackerspace or a carpenter friend nearby, you'll save most of the tool costs.

Common beginner mistakes

  • Mixing up gross and net volume. The calculation gives the net volume of air. The driver, port, bracing and crossover take up space that you have to add on top. In a small cabinet, that can easily mean tuning errors of tens of percent.
  • A crossover from an online calculator. It assumes a constant impedance that no driver has. The result can have a hole or a hump at the crossover point.
  • Cutting before you have the drivers in your hands. Check the cut-out sizes and recess depth on the actual part. The catalogue sometimes differs from reality.
  • A leaky cabinet. Glue joints along their full length and seal the holes for cables and terminals. In a bass reflex, a leak changes the tuning and whistles.
  • Wrong polarity. A tweeter wired the wrong way round creates a deep dip at the crossover point. With some crossovers, though, reversed polarity is intentional, so stick to the schematic.
  • Coils packed tightly together or next to a magnet. They influence each other. Space them apart and turn them 90°.
  • Ignoring the baffle step. The speaker then sounds thin and harsh, even though the drivers are good.
  • Underestimating the finish. MDF edges soak up paint like a sponge. Without primer and sanding between coats, the surface won't be smooth.
  • A first project that's too ambitious. A three-way tower or a back-loaded horn as a first build often ends up unfinished. Start with a small two-way or a full-range driver.
  • Not comparing with anything. Without comparing against another speaker at the same volume, you don't know whether you got it right. A blind ABX test helps, as does measuring as described in How to measure a loudspeaker.

Resale value

Ready-made speakers from a well-known brand are easy to sell. Second-hand, you usually get about half the original price for them, more for popular models and less for lesser-known ones.

Home-built speakers are hard to sell. The buyer doesn't know how they sound, there are no reviews, and they can't tell how well they're built. Often you'll get only the price of the drivers, or less. The exception is well-known proven designs with documentation and a nice finish. Those find buyers among other DIYers.

On the other hand, the drivers from your own build don't lose value as quickly. You can take them out and reuse them in your next project. That doesn't work with a ready-made speaker.

So if you plan to replace your speakers in two years, ready-made ones are the safer investment. If you want to keep them for ten years, resale value hardly matters.

When to buy, when to build

SituationRecommendation
Budget up to €300 a pairBuy. Big brands are cheaper here than anything you can build.
Budget €300 to €800 a pair, no tools or experienceBuy, or get a kit with a pre-cut cabinet if you enjoy working with your hands.
Budget from €800 a pair, keen to make somethingBuild a proven design or a kit. This is where the savings are biggest.
You need an unusual size or lookBuild. You can hardly buy a made-to-measure speaker.
You want to learn how speakers workBuild, a proven design first, then your own.
You have no time and want music this weekendBuy.
You live in a small flat with no workshopBuy, or get a kit with pre-cut parts.
You want to sell the speakers in a few yearsBuy a well-known brand.
You want a big subwoofer or a horn systemBuild. Ready-made ones are very expensive and the cabinet is simple here. See the article Subwoofer.

One piece of advice holds either way: placement and the room have the biggest influence on the final sound. More in the article The room plays along and in the room planner.

How Loudsmith helps

Loudsmith is a free in-browser app that shrinks exactly the risks that put people off building.

  • Ready-made templates and designs from the gallery. With one click you can open a bookshelf, tower or subwoofer template, our Needle and other designs from the gallery on the home page. You'll see their response, crossover and drawing before you buy anything, and you can keep tweaking them.
  • Choosing drivers and a cabinet. The design guide asks where you'll be listening, how much bass you want and how big the speaker can be, then finds suitable drivers. After that it compares cabinet types and calculates the dimensions.
  • A crossover with real impedance. The design works with the driver's actual impedance and response, not a constant resistance. Automatic checks flag problems before you buy anything.
  • Drawing and cut list. You can save the cut list with panel dimensions as a CSV and take it to the timber yard for cutting. It comes with numbered build steps.
  • Shopping list. The shopping list with prices and stock levels shows your budget before you start building. You can tick off things you already have at home.
  • Crossover circuit board. The board editor lays out the parts so the coils don't interfere with each other.
  • Comparing measurements with the design. Once you've measured your speaker, upload the measurement and Measurement vs. design suggests specific crossover fixes. The comparison is relative, so even an uncalibrated microphone will do. The speaker measurement page shows how to measure.

You can start right away in the app. Even if you end up buying speakers, it's worth seeing there how different designs behave. You'll understand much better what you're buying.

Key takeaways

  1. With a ready-made speaker, you mainly pay for the chain, not the drivers. Drivers make up roughly a tenth of the shelf price.
  2. Building pays off from the mid-range upwards. For €400 to €500 in materials, you get the parts of a speaker that would cost two to four times as much in a shop.
  3. The cabinet is a craft, the crossover is engineering. Without measurements or a proven design, it's the biggest risk.
  4. First build: a proven design or a kit. Your own design only once you can measure.
  5. Buy cheap speakers. Under €300 a pair, you won't beat a big brand at home.

The best part is that you don't have to decide blindly. In Loudsmith you can design a speaker for free in an evening and see its response, dimensions and parts cost. Then decide whether to build it, or head to the shop knowing a lot more.

Short glossary

  • Driver: the actual "speaker" with a cone and a magnet, mounted in the cabinet.
  • Crossover: a circuit of coils, capacitors and resistors that splits the signal between the drivers.
  • Kit: a set of drivers, crossover and sometimes cabinet parts based on a proven design.
  • Proven design: a design that someone has measured, fine-tuned and published with a drawing and schematic.
  • Margin: the part of the selling price that covers the seller's costs and profit.
  • Net volume: the volume of air in the cabinet after subtracting the drivers, bracing and port.
  • Baffle step: a bass drop of up to about 6 dB as low frequencies spread from the front panel into the whole room.
  • FRD and ZMA: text files with measured frequency response and impedance.
  • MDF: medium-density fibreboard, the most common material for speaker cabinets.

Sources: F. Toole, Sound Reproduction: The Acoustics and Psychoacoustics of Loudspeakers and Rooms (3rd ed., Routledge 2017); V. Dickason, The Loudspeaker Design Cookbook (7th ed., Audio Amateur Press 2006); J. Krutke, Zaph Audio (design archive); P. Carmody, advice for beginners on the author's website; Slovak VAT Act No. 222/2004 Coll. as amended from 1 January 2025 (23 % rate); driver and part prices from the SoundImports catalogue as used in the bookshelf speaker article. Price shares and margins are a rough model, not data from specific companies.

Free tools: Room planner · Speaker measurement · Blind ABX test